Curse

DM00 · Feb 22, 2005, 04:17 AM // 04:17

I have a Netgear WGR614v5, and I cannot connect to Guild Wars. I have the port they listed in my port forwarding (TCP/UDP Port 6112), still no dice. Luckily, I have an old router, that I could use during BWE, but no hardware firewall. Anyone have any advice/techniques to using my new router without replacing it every time I want to play, or disabling the firewall altogether? What about the port listed, is it correct? Thanks...

DM

Genosha · Feb 22, 2005, 06:30 AM // 06:30

There are a couple of ways to address this:

1. Port Triggering - This tells the router to open a port at a specific time when accessed (Port specific). Security Issues - None really it's only temporary.

2. Port Fowarding - Which tells the router to open specific ports for communication to a specific location (Port specific). Security Issues - Very little really it only routes it to a specific computer.

3. DMZ (Demiliterized Zone) - This tells the router that all ports are opened and accessible (Port All). Security Issues - Serious because you have NO security of the router at ALL.

Try the first 2 either can work.

Try the 3rd only if desprate.
IF you do use option 3 Please use a software firewall other than windows (Sygate or ZoneAlarm etc.which can be found on Cnet for free), but windows will do if you don't want to use another.

This should apply to all routers.

Note: A software firewall is always a good option with or without a router firewall.

Darkmane · Feb 22, 2005, 08:14 AM // 08:14

Quote:

Originally Posted by DM00

I have a Netgear WGR614v5, and I cannot connect to Guild Wars. I have the port they listed in my port forwarding (TCP/UDP Port 6112), still no dice. Luckily, I have an old router, that I could use during BWE, but no hardware firewall. Anyone have any advice/techniques to using my new router without replacing it every time I want to play, or disabling the firewall altogether? What about the port listed, is it correct? Thanks...

DM

Make sure your router has the latest firmware. Your port forwarding may be working fine but if your Hardware firewall is still blocking the port...... your not forwarding anything. I have the chincy windows firewall turned on with my computer and a router. I can play the game just fine without windows's firewall throwing any red flags.

Acronym · Feb 24, 2005, 04:49 PM // 16:49

Quote:

Originally Posted by Genosha

There are a couple of ways to address this:

1. Port Triggering - This tells the router to open a port at a specific time when accessed (Port specific). Security Issues - None really it's only temporary.

Gemosha is correct You router has a function called port triggering. If not set the port forwarding will not work. Both have to be enabled to work. Also if you have software firewall installed in use with your router firewall can cause problems.

DM00 · Feb 25, 2005, 02:50 AM // 02:50

Actually, I had enabled Port Forwarding, on port 6112 (as I stated in my first post). I was still getting the "Unable to Connect Err=5" message.

I took Darkmane's advice and started playing with the hardware firewall settings. I got some time to fully play with setting in the router tonight, and turning off the SPI firewall, but leaving on the NAT protection, worked.

If you have the router (or a similar router with the same types of protection), and want my settings, I'd be happy to post them.

DM

sovelocity · Jul 12, 2005, 05:55 AM // 05:55

I actually have the exact same router model as you described and would love it if you posted the router settings. Thanks!

Ukukwi · Nov 08, 2005, 07:51 PM // 19:51

I have the same model router and I had to disable Stateful Packet Inspection (SPI) to allow GW through.

I do this whenever I want to play, but then I re-enable SPI when I'm done.

Jadeleaf · Feb 12, 2006, 09:22 PM // 21:22

I got me a belkin f5d7632-4 wireless g router, ive tried portforward.com and tonns of other websites. Im sure there is something im missing. I have no firewall on either pc or router (< crazy noob eh? :P) and still i cannot get past the CONNECTING PART before GW starts up. I added the port numbers into my routers 'virtual servers' section, and tried with the 'application gateway' section; still no luck.... Anybody got the same router? I'd kill for your settings.... cheers.

Ase123 · May 01, 2006, 12:58 PM // 12:58

yer
ive got a belkin router
aparantly
its to do with the nat built in to it
but i still cant fix it!!!!
help me

Trinitron6_03 · May 01, 2006, 11:51 PM // 23:51

like posted above, make sure the firmware is updated.

then make sure you have port triggering enabled

now. you can also set your computer for a static ip, and you can port forward to your ip. thats another simple fix.

The Kannon · Apr 29, 2007, 01:04 PM // 13:04

I have the exact same router, and had the same problem.

Simple fix for me was updating to the latest firmware.